英语翻译GMS 微波物位开关由三个电器隔离的单元构成：发射器、接收器与放大器,发射器与接收器相互成对安装.为获得良好的性能需确保接收器、发射器的安装是牢固且是严格正对的.发射器

英语翻译GMS 微波物位开关由三个电器隔离的单元构成：发射器、接收器与放大器,发射器与接收器相互成对安装.为获得良好的性能需确保接收器、发射器的安装是牢固且是严格正对的.发射器
英语翻译
GMS 微波物位开关由三个电器隔离的单元构成：发射器、接收器与放大器,发射器与接收器相互成对安装.为获得良好的性能需确保接收器、发射器的安装是牢固且是严格正对的.发射器向具有微波侦测能力的接收器发送微波束,微波束每秒发送 200 次,当在接收器同一平面出现吸收微波的物料时,微波束将不能到达接收器,因而接收器将不能侦测到微波束.
当接收器端侦测到微波束,状态改变时将会触发继电器动作.从侦测到微波系列状态改变到继电器动作的时间延迟长度由两个可单独调节的电位器设置；一个用于设置信号有效而触发的继电器,另一个用于设置信号中断而触发的继电器,继电器的动作总在信号状态改变
并维持到已设置的时间长度之后.在延时时间段内任何的状态改变将会使延时重新开始.
接收器的灵敏度由一电位器调整,经过调整,可使不同物料间的反射率与吸收率得到补偿.同样的,我们也可调整至即使仅是侦测到部分的微波束,也可改变触发状态.系统有两个电位器用于灵敏度的调节,分别用于粗调与细调.当侦测到信号中断时,继电器状态可被
设置为得电或失电,此工作模式可由接收器端的二值开关设置.
放大器设置了三个 LED 指示灯,分别用于指示供电电源；有效信号；继电器得电.而发射器上仅有一个指示灯用于指示供电电源.

英语翻译GMS 微波物位开关由三个电器隔离的单元构成：发射器、接收器与放大器,发射器与接收器相互成对安装.为获得良好的性能需确保接收器、发射器的安装是牢固且是严格正对的.发射器
GMS Microwave level switch electrical isolation unit consists of three components:a transmitter,receiver and amplifier,transmitter and receiver each other in pairs.In order to obtain good performance need to ensure that the receiver,the transmitter is securely mounted and is a strictly positive right.The transmitter sends to the receiver's ability to detect the microwave having a microwave beam,the microwave beam is transmitted 200 times per second,when the microwave-absorbing material in the same plane as the receiver,the microwave beam will not reach the receiver,the receiver will not detect and therefore measured microwave beam.
When the receiver detects a microwave beam ends,the status change will be triggered when the relay.From the detected state to a series of microwave relay delay time length is set by two separately adjustable potentiometer; effective and a trigger signal for setting the relay,and one for the relay triggered interrupt signal relay The total movement in the signal state change
And to maintain the length of time after you have set.The delay period will cause any change in the status of the delay to start again.
By a receiver sensitivity adjustment potentiometer,after adjustment,and make the reflectivity of the absorption rate between the different materials to be compensated.Similarly,we have to adjust to be detected even if only part of the microwave beam can also change the trigger condition.There are two systems for sensitivity adjustment potentiometer,respectively,for coarse and fine adjustment.When the detected signal is interrupted,the relay status can be
Set energized or de-energized,this mode of the receiver side by binary switch settings.
Amp set up three LED indicators are used to indicate the power supply; valid signal; relay is energized.While the transmitter is only one indicator to indicate power supply.